Dentsply Integrity Temporary Crown And Bridge Material - A2

Dentsply Integrity Temporary Crown and Bridge Material with Fluorescence is a two-component, automixed material for durable and aesthetic temporary restorations. Its consistent texture and minimal shrinkage simplify handling, reducing adjustments and saving time. Conveniently packaged in a cartridge, it allows easy application with minimal waste.

₹8,795.00
Out of stock
SKU
SBDEN06352
Price: 8,795.00 (Inclusive of Taxable Goods)

Contact us for sales assistance from our Biomedical Engineer.

Prashanth Reddy V | Senior Sales Executive

+91 9063507429

[email protected]

Features:

  • Ensures an optimal mix ratio without cross-contamination
  • Maintains a temperature change of less than 5°C in the mouth during setting
  • Gentle on the pulp, providing excellent patient comfort
  • Self-bonding for easy repairs
  • Polishes to a natural shine for outstanding aesthetics
  • Smooth consistency for effortless handling and cleanup
  • Superior esthetics
Technical Details
Technical Specification
  • Immediately before each use - Bleed cartridge prior to inserting new mix tip
  • 0-5 seconds - Material dispensed into preliminary impression
  • 5-45 seconds - Material inserted into the mouth
  • 2-3 minutes - Removal from mouth
  • 6 minutes - Remove the O2-inhibited layer and begin to trim the excess with-rotary instruments
  • 7 minutes - Complete contours and polish

Composition:  

  • Barium glass
  • Fumed Silica
  • Methacrylate Monomers
  • Catalyst
  • Stabilizers
  • 1x 76gm Cartridge
  • 15 x Small Mixing Tips
  • Raise the release lever vertically upward, while simultaneously pulling the plunger all the wayback in the dispenser handle.

Cartridge Loading :

  • Open cartridge lock by lifting up top clasp.
  • Orient and insert cartridge with notch facing down.
  • Close the top clasp to lock cartridge into dispenser gun.
  • Remove the cartridge cap by turning 90° counterclockwise. Discard the cartridge cap.
  • The used mixing tip can be disinfected and left in place until the next use to serve as a self-sealing cap.

Dispensing :

  • Dispense and discard a “pea” size amount of base and catalyst before installing mix tip to ensure even flow from cartridge. Use gentle pressure. Be sure no plug is present. If any plug blocks flow, clear with an instrument. Wipe away excess from the cartridge carefully so base and catalyst do not cross contaminate and cause obstruction of the nozzle.
  • Install a mixing tip on the cartridge by lining up the notch on the outside rim of the mix tip with the notch on the cartridge flange. If mix tip does not seat easily, be sure the internal end view of the mix tip is aligned correctly. The mix tip itself can turn in its cap.
  • The two holes should line up with the piece that is on the outside rim of the mix tip cap to facilitate inserting. Turn tip to align in its cap.
  • When mix tip notch is lined up with the notch on the cartridge flange, turn mix tip cap 90° in a clockwise direction to lock in place on cartridge.
  • Squeeze dispenser trigger with moderate and even pressure to begin mixing/dispensing material. Material will stop flowing after trigger is released. Disinfect barrels and used mix tip for storage. Immediately prior to next use, bleed syringe and install new mix tip as outlined above.
  • To remove cartridge, push up lever and pull slide flush. Lift plastic lever on the top of gun and remove cartridge.
  • Dispense a small amount through the mix tip onto a mixing pad and discard. Without delay, begin dispensing Integrity Material directly into the preliminary impression into the area of the preparation by applying continuous, light pressure to the dispensing apparatus handle. As the material comes out of the mixing tip, inject it into the deepest portion of the preliminary impression and then into the gingival areas, keeping the mixing tip immersed in the material to prevent bubbles. Reseat the preliminary impression into the patient’s mouth in the proper relative position within 45 seconds of the start of mix.
  • Leave impression in place for approximately 2-3 minutes from the start of the mix.
  • Remove the impression containing the Integrity Material restoration during the firm elastic stage.
  • At this elastic phase, gross excess may be quickly trimmed with sharp scissors, being careful not to distort the restoration or margins.

Contact us for sales assistance from our Biomedical Engineer.

Prashanth Reddy V | Senior Sales Executive

+91 9063507429

[email protected]

WA button WA button
Copyright © 2023-present SignelbioMedical, Inc. All rights reserved.